If your washer smells musty or leaves black spots on clothing, mold may be growing in hidden seals, dispensers, or the drum.
This guide explains how to remove mold from a washing machine and keep it from coming back.
Why mold grows in washing machines
Washing machines create the perfect environment for microbial growth: moisture, warmth, detergent residue, and poor airflow.
Front-load washers are especially prone because their rubber door gaskets can trap water and lint, but top-load models can also develop mold in lids, dispensers, and drain areas.
Mold and mildew commonly form when the machine is left closed after cycles, loads are washed in cold water only, or too much detergent and fabric softener are used.
Over time, the buildup can cause persistent odors, discoloration, and residue transfer to laundry.
Signs your washing machine has mold
- Musty or sour odor coming from the drum or gasket
- Black, green, gray, or pink residue on rubber seals
- Visible film in the detergent drawer or around the dispenser
- Clothes smelling damp after washing
- Dark spots on towels, activewear, or bath items
- Water pooling in the door seal, drum edge, or soap tray
What you need before cleaning
Before starting, gather basic supplies and check your washer manual for manufacturer-approved cleaners.
Some brands recommend specific cleaning cycles or warn against certain chemicals on stainless steel, rubber, or electronic components.
- Microfiber cloths or soft sponges
- Rubber gloves
- White vinegar or an oxygen bleach cleaner
- Baking soda, if needed for odor control
- Old toothbrush or soft detailing brush
- Warm water
Avoid mixing vinegar with chlorine bleach, because that can create dangerous fumes.
If you plan to use bleach, rinse thoroughly before using any other cleaner.
How to remove mold from a washing machine?
The best method depends on whether your washer is front-load or top-load, but the overall process is similar: clean removable parts, scrub visible mold, then run a hot cleaning cycle to flush residue from internal surfaces.
1. Unplug and empty the machine
Turn off the washer and unplug it if possible.
Remove all laundry and inspect the drum, gasket, dispenser, and door areas for visible buildup.
2. Clean the door gasket or lid area
For front-load machines, gently pull back the rubber gasket and wipe away debris, mildew, and trapped moisture.
Use a cloth dampened with warm water and a small amount of cleaner, then scrub crevices with a soft brush.
For top-load washers, wipe around the lid, rim, and underside where residue often collects.
3. Remove and wash the detergent drawer
Detergent and softener trays often hold sticky residue that feeds mold growth.
Remove the drawer if your machine allows it, soak it in warm water, and scrub the compartments thoroughly.
Dry it completely before reinstalling.
4. Clean the drum
Wipe the drum interior with a cloth and a mild cleaning solution to remove film and grime.
If the mold is light, white vinegar can help loosen buildup and neutralize odors.
For heavier growth, a washer-safe oxygen bleach product may be more effective, especially on non-porous metal surfaces.
5. Run a hot cleaning cycle
Run the washer on the hottest setting available, using either a washing machine cleaning tablet, oxygen bleach, or the machine’s self-clean cycle if it has one.
This helps dislodge hidden residue in hoses, pumps, and internal surfaces.
If odors persist, repeat the cycle once more.
6. Wipe and dry every surface
After the cycle ends, leave the door or lid open and wipe away any remaining moisture.
Dry the gasket, glass, drum edge, detergent tray, and exterior seals.
Mold grows quickly in damp spaces, so drying is just as important as cleaning.
What is the best cleaner for mold in a washing machine?
For routine maintenance, white vinegar and hot water can help reduce soap scum and odor.
For stubborn mold stains, an oxygen bleach cleaner or a commercial washing machine cleaner is often more effective because it targets buildup without the harshness of chlorine bleach in many situations.
Chlorine bleach can disinfect some surfaces, but it should be used carefully and only when the manufacturer allows it.
It is not ideal for every washer, especially if your appliance has specialty finishes or if you are unsure about material compatibility.
If you prefer a natural approach, baking soda can help with odor, but it is usually better as a supporting cleaner than as the sole solution for visible mold.
How to clean a front-load washer with mold
Front-load washers need special attention because the door gasket is the most common problem area.
Clean the folds of the rubber seal, the lower lip where water collects, and the glass door edge after every few loads if needed.
- Wipe the gasket after each wash
- Leave the door ajar between loads
- Use high-efficiency detergent only
- Reduce fabric softener use
- Run a hot maintenance cycle weekly or biweekly
How to clean a top-load washer with mold
Top-load washers can still develop mold around the lid, bleach dispenser, agitator, and rim.
If your model has a removable fabric softener cup or dispenser insert, clean it separately and check the underside of the lid for hidden residue.
- Inspect the lid seal and underside regularly
- Wipe the tub rim after wet loads
- Clean the agitator and dispenser ports
- Use the hottest water safe for your fabrics during maintenance cycles
How to prevent mold from returning
Prevention depends on controlling moisture and residue.
A clean washer can still grow mold again if it stays damp or overloaded with detergent.
- Leave the door or lid open after each cycle
- Remove wet laundry promptly
- Use the recommended amount of detergent
- Avoid excessive liquid fabric softener
- Run regular hot cleaning cycles
- Wipe seals, dispensers, and the drum weekly
- Check and clean the drain pump filter if your washer has one
Using the right detergent matters too.
High-efficiency washers need HE detergent, and using too much can leave a film that supports mold growth.
If you wash mostly in cold water, add a periodic hot cycle to cut buildup.
When mold means a bigger problem
If mold keeps returning after repeated cleaning, the issue may involve standing water, a clogged drain line, a faulty door seal, or a blocked filter.
Persistent leaks, water not draining fully, or visible mold inside hoses and inaccessible components may require professional service.
Call an appliance technician if you notice electrical issues, recurring drainage problems, or mold that appears deep inside the machine where you cannot safely clean it yourself.
In severe cases, replacement of the gasket or dispenser parts may be more effective than repeated surface cleaning.
Helpful maintenance schedule
- After every wash: leave the door or lid open and wipe visible moisture
- Weekly: clean the gasket, door glass, and detergent drawer
- Monthly: run a hot maintenance cycle
- Every few months: inspect hoses, filters, and dispensers for buildup
Following this routine keeps the washer fresher, reduces odors, and helps protect fabrics from residue and mold transfer.