How to Fix a Leaking Bathroom Drain
A leaking bathroom drain can waste water, damage cabinets, and create mold behind walls or under flooring.
This guide explains how to identify the source, tighten common connections, replace worn seals, and know when the problem needs a plumber.
What causes a bathroom drain to leak?
Bathroom sink and tub drains usually leak at a few predictable points.
The most common causes are loose slip nuts, degraded plumber’s putty, cracked gaskets, corroded metal parts, and misaligned drain assemblies.
- Loose threaded connections: The drain body, tailpiece, or trap may have loosened over time.
- Worn seals: Rubber washers and gaskets can dry out, flatten, or split.
- Failed plumber’s putty or silicone: The seal under the drain flange may no longer hold.
- Cracks in pipes: ABS, PVC, or metal drain lines can develop hairline fractures.
- Clogs and pressure: Partial blockages can force water to escape at weak joints.
How do you find the leak source?
Before removing parts, identify where the water appears.
Dry the entire area with a towel, then run water in the sink or tub while watching every joint with a flashlight.
Check these common leak points
- Drain flange: Look for water around the top opening of the sink or tub drain.
- Tailpiece connection: Check the vertical pipe below the drain body.
- P-trap or trap arm: Inspect the curved trap and the pipe leading into the wall.
- Overflow assembly: On tubs and some sinks, the overflow gasket may be leaking.
- Wall penetration: Water coming from inside the wall may point to a trap arm or supply issue nearby.
If you are troubleshooting a bathroom sink, place dry paper towels under each joint.
The first damp spot often reveals the exact failure point.
What tools and materials do you need?
Most drain repairs require basic hand tools and a few inexpensive plumbing supplies.
Having the right parts ready makes the repair faster and reduces the chance of repeat leaks.
- Adjustable wrench or channel-lock pliers
- Basin wrench for tight sink connections
- Screwdriver
- Bucket and old towels
- Flashlight
- Replacement washers or gaskets
- Plumber’s putty or 100% silicone, depending on the fixture
- Pipe joint compound or thread sealant if needed
- Replacement P-trap or tailpiece if damaged
How to fix a leaking bathroom sink drain
Most sink drain leaks are caused by a loose connection or a failed seal at the drain flange.
Follow these steps in order, starting with the simplest fix.
1. Tighten the visible connections
Use your hand first, then a wrench if needed, to snug the slip nuts on the tailpiece and P-trap.
Do not overtighten plastic fittings, because they can crack or distort the washers.
2. Inspect and replace washers
Disassemble the trap if the leak continues.
Look for flattened, brittle, or misaligned rubber washers.
Replace any worn washer and reassemble the joint carefully, making sure the tapered side faces the correct direction when applicable.
3. Remove and reseal the drain flange
If water leaks from the top of the sink or around the drain body, remove the drain assembly from above.
Clean old plumber’s putty from the sink and flange, then apply a fresh bead of plumber’s putty or silicone, depending on the sink material and manufacturer instructions.
Tighten the drain body evenly from below, wipe away excess sealant, and allow the sealant to cure if you used silicone.
4. Check the pop-up assembly
For sinks with a pop-up stopper, the pivot rod and gasket can leak if the retaining nut is loose or the washer is worn.
Remove the rod, clean the parts, and reinstall with a fresh gasket if needed.
How to fix a leaking bathtub drain
Bathtub drain repairs often involve the drain shoe, overflow plate, or the gasket between the tub and drain body.
Because tubs hold a larger volume of water, even a small leak can cause serious damage.
Replace the overflow gasket
If the leak happens only when the tub is filled, the overflow gasket may be the problem.
Remove the overflow cover plate, pull the assembly forward if needed, and replace the gasket with a new one sized for the drain model.
Reseal the tub drain flange
A leaking tub drain flange usually means the sealant has failed.
Remove the drain with a tub drain removal tool, clean the old compound, and reinstall using fresh plumber’s putty or the sealant recommended by the tub manufacturer.
Inspect the waste and overflow assembly
Older tubs often use a waste-and-overflow system with several joints.
Tighten the connections and replace any cracked elbows, corroded metal parts, or damaged gaskets before reassembly.
Should you use plumber’s putty or silicone?
The right sealant depends on the fixture and the drain material.
Plumber’s putty is commonly used on metal drain flanges, while silicone is preferred for some plastic fittings and manufacturer-specific applications.
- Use plumber’s putty: When the product instructions allow it and the surface is compatible.
- Use silicone: When a permanent waterproof seal is needed or putty is not recommended.
- Do not guess: Check the drain kit instructions, especially for acrylic, fiberglass, and specialty finishes.
Using the wrong sealant can cause future leaks or damage certain surfaces, so always match the sealant to the fixture.
When should you replace the drain instead of repairing it?
Some drains are too deteriorated to seal reliably.
Replacement is usually the better choice if the drain is cracked, heavily corroded, stripped, or leaking after repeated repairs.
- The metal drain body is rusted through
- Plastic threads are stripped or cracked
- The washer groove is damaged
- The drain leaks again after a proper reseal
- Water has caused rot around the fixture opening
Replacing the entire drain assembly often costs less than repeated temporary fixes and reduces the risk of hidden water damage.
How can you prevent future bathroom drain leaks?
Preventive maintenance keeps drain joints tight and seals intact.
A few simple habits can extend the life of the drain assembly and reduce plumbing emergencies.
- Check under sinks monthly for moisture or staining
- Avoid over-tightening plastic fittings
- Clear hair and soap buildup before it becomes a blockage
- Replace aging washers during routine maintenance
- Use drain parts that match the fixture and pipe size exactly
- Watch for slow drips after heavy use, especially around tubs
When is it time to call a plumber?
Call a licensed plumber if the leak is inside a wall, the pipe is corroded, the fixture base is loose, or the repair requires cutting into plumbing.
Professional help is also wise if you smell mold, see water damage on the ceiling below, or cannot stop the leak after replacing seals and tightening joints.
A plumber can also test for hidden leaks, identify code issues, and replace damaged drain assemblies with the right fittings for your bathroom.
What should you check after the repair?
After reassembly, run water for several minutes and inspect every joint with a dry paper towel.
Fill the sink or tub, drain it fully, and look for drips while water is flowing and after the fixture empties.
Recheck the area the next day as well.
Some leaks only show up after the fixture has dried or after the trap settles into place.